Trade show booth rental in Chicago
Chicago has a reputation as a difficult union floor, and it is only half deserved. McCormick Place publishes an Exhibitor Bill of Rights that lets your own employees build a booth of any size with their own hand tools — broader latitude than several cities with gentler reputations. The limits are specific, and worth knowing before you accept a labor estimate.
- Main venue
- McCormick Place
- Labor
- Union, with published rights
- Exhibitor self-setup
- Permitted, any booth size
- Hard limit
- No motorised equipment
What your own staff may do
The useful thing about McCormick Place is that the answer is published rather than negotiated. These are the four points that decide whether you are paying for install labor at all.
The rights are written down
McCormick Place publishes an Exhibitor Bill of Rights setting out what your own people may do on the floor. Read it before you accept a labor estimate — it is more permissive than the city's reputation suggests, and vendors do not always volunteer it.
Any booth size, your own tools
Exhibitor employees are permitted to set up and dismantle exhibits in a booth of any size using your own ladders and hand tools, along with cordless and other tools the venue designates. There is no square-footage ceiling on that right.
Who counts as an employee
The definition is specific: someone employed full-time by the exhibiting company for at least six months before the show opens. This is the part that gets challenged on the floor, so send people who clearly qualify and have them carry company identification.
Where the right stops
Motorised and hydraulic equipment is off limits at all times — forklifts, scissor lifts, genie lifts, scaffolding, pallet jacks, motorised dollies. If your install needs any of it, that is a labor call regardless of who your staff are.
Labor rules are set per event as well as per venue. Everything here is a starting point — the exhibitor kit for your specific show is the document that governs, and your vendor will design and quote against it.
Planning around the building
Freight is a separate question
Self-setup rights cover assembling your booth. They do not make you your own material handler — crates still move through the official contractor, and drayage is billed on weight either way.
Find out which hall
McCormick Place is the largest convention centre in North America, spread across multiple buildings. Which hall you are in changes dock access, move-in timing, and how far your freight travels inside the building.
Mind the biennial calendar
Several of the largest shows here run every other year — IMTS, the manufacturing technology show, is the best known. In an on year, inventory and labor across the whole city tighten.
Book against the hall, not the city
Ask a prospective vendor how often they install in your specific building, not whether they work Chicago. See what drives the quote.
What moves a Chicago quote
Two forces pull in opposite directions here: unusually broad self-setup rights push labor down, and a very large building pushes freight up.
Self-setup can remove a real line
On a 10 × 10 or 10 × 20 that your own team can stand up, the exhibitor rights here genuinely cut the install and dismantle lines. That is unusual among large union venues and worth exploiting.
Drayage does not move
Material handling is unaffected by who assembles the booth. It is billed by weight with a minimum, in both directions, and on a big-hall show the internal distance from dock to space is not trivial.
Overtime windows are expensive
Late move-in slots and weekend work push labor into premium rates. On a floor this size, move-in runs for days and the good slots go to whoever asked first.
Local inventory is deep
Chicago has a large concentration of exhibit houses, so stock configurations are easier to source here than in thinner markets — which keeps you away from custom fabrication, the fastest way to grow a quote.
Common questions
Can I set up my own booth at McCormick Place?
Yes, within defined limits. The venue publishes an Exhibitor Bill of Rights allowing exhibitor employees to set up and dismantle a booth of any size using your own ladders and hand tools, plus cordless and other designated tools. The catch is the definition of "employee" — full-time with the exhibiting company for at least six months before the show — and a flat prohibition on motorised or hydraulic equipment.
Do I still pay drayage if my own staff build the booth?
Yes. Assembling the exhibit and moving freight are separate jurisdictions. Material handling goes through the show's official contractor and is billed by weight regardless of who puts the walls up. The only common way around it is carrying genuinely hand-portable items in yourself, which does not describe a rental booth.
Is Chicago an expensive city to exhibit in?
It is a union market with big-hall freight distances, so it is not cheap — but the exhibitor self-setup rights are broader than in several other major cities, which can offset the labor line on smaller booths. Compare a Chicago quote against Dallas or Atlanta if you have a choice of venue.
How far ahead should I book a booth rental in Chicago?
Six to twelve weeks for a standard linear booth, three to four months for an island, and longer if your show falls in an on year for one of the biennial giants. Inventory across the whole city tightens when a very large show is in the building.
Does my vendor need to be based in Chicago?
No, but there are real advantages to one who is. A local exhibit house ships a shorter distance, knows the building's dock behaviour, and can put a person on site if something arrives damaged. Those are the things that turn into surprise line items when they go wrong.
Comparing cities? Dallas and Atlanta are right-to-work and generally cheaper to install in, while Los Angeles splits the work between two unions. All fifteen are side by side on the city comparison.
Get info